REFERENCE PROJECTS:

​

General-purpose IP-based control system design

(Design of Main Board and Power Board and Connector Boards).

• MIL-STD-810F

• MIL-STD-461F

• MIL-STD-1275D

• MIL-STD-464C

• System Design

• Block Diagrams

• PCB design(16 Layer/Analog/Digital/Power signals)

• 0.5mm BGA package PCB design

• 2mm PCB thickness

• Use of 0.65mm and 1mm BGA MCU (STM32F7 and STM32F4 series)

• Use of 0.5mm BGA FPGA (Xilinx Spartan7 series)

• Power management, Super Capacitor

• Isolated ports and isolated power supply

• RS232, RS485, I2C, I2S, SPI, UART, USB, Ethernet, CAN BUS, Clock, Audio signals, Analog/digital Sensor signals, LVDS (Low-Voltage Differential Signaling), Analog signals, 1-Wire signals, use of parallel interfaces

• Isolated CAN BUS usage, isolated RS485 usage, isolated USB usage, Transformer shielding, Ethernet Phyter transformer,  other signals requiring isolation

• Flash memory, CODEC, Temperature Sensor, uSD Card, JTAG, Serial port, Audio circuits, Gyroscope usage

• Circuit simulaiton (PSPICE, LT Spice and NI Multisim)

​

Half brick DC/DC Module Design (Po=150W, Input Voltage 9-75 VDC)

 

• Half Brick DC-DC Module

• 8:1 Input voltage range (9-75VDC)

• 150W İsolated output

• Efficiency up to 90%

• Fixed Switching Frequency

• UVLO Input Voltage Protection

• Over Temperature Protection

• Over Voltage / Current Protection

• Remote On/Off

• Industry Standard Half Brick Pack (Half Brick)

• Fully Isolated 1500VDC

• Conforms to UL60950-1 2 Standard

• COTS can be used as a product.

• Ease of use with MIL-STD-1275

• Ease of use with MIL-STD-704

​

Active EMI Filter (AEF) Design

• Active EMI filter module design

• MIL-STD-461 (CE101, CE102)

• 25dB/uV EMI damping

• Circuit simulaiton (LT Spice and NI Multisim)

​

Laser Warning System Design

• MIL-STD-810F

• MIL-STD-461F

• MIL-STD-1275D

• MIL-STD-464C

• System Design

• Block Diagrams

• Dark side photodiode sensor usage

• DC-DC converter design with -100VDC, -450VDC, -55VDC output voltage.

• TIA (Transimpedance amplifier design)

• Filter design and simulation in high impedance TIA circuits(Band Pass Filter, Low pass Filter, High Pass Filter).

• Circuit simulaiton (LT Spice and NI Multisim)

​

Design of remote data collection and cloud storage system for wind turbines

• Detection of different sensors

• Data Acquisition Card

• IEC 61850 communication

• USING AS A POWER OVER BUS (FOR RS485)

​

FADEC (Full Authority Digital Engine Control)

• Power supply management

• Boost converter design for injection

• Motor Control Circuit Design

• ECU (Electronic Control Unit)

• Relay Unit

• PSPICE Simulation

• Filter Cards (MIL-DTL-38999 connectors)

• Peak and hold type injector driver

• H-Bridge driver

• RTCA/DO-160

• MIL-STD-461

• MIL-STD-810

​

Military Intercom System

• PoE (Power Over Ethernet) designing

• Power supply designing (Central Unit )

• Power supply designing (System Unit-1 )

• Power supply designing (System Unit-2 )

• Handheld Controller (Tablet PC without battery) PCB designing

• Hot-swap controller usage

• MIL-STD-461

• MIL-STD-1275

• MIL-STD-810

​

​Design of Hand-held Military Computer motherboard and power card

• MIL-STD-461

• MIL-STD-1275

• MIL-STD-810​

• Two-battery automatic charging system

• PCB design(10 Layer/Analog/Digital/Power signals)

• System Design

• Block Diagrams

• 2mm PCB thickness

​

Smart Battery Charger Unit​ for Hand-held Military Computer

• MIL-STD-1275

• Military battery working conditions

• Two-battery automatic charging system

• PCB design(4 Layer/Analog/Digital/Power signals)

• Use of STM32F103

• 1.6mm PCB thickness

​​

Military Ship Alarm&Anouncement Power Supply

(TCG Anadolu Project: The design and military tests of the Alarm & Announcement System of the Turkish Battleship (TCG Anadolu) and the main power unit of our PBX operating the system)

• Redundant using

• Hot-plug design

• 1.5kW + 1.5kW=3kW output power

• Use of Hold-up capacitor block

• MIL-STD-810G

• MIL-STD-461F

​

Military Submarine Alarm&Anouncement Power Supply

(Submarine Project: The design and military tests of the Alarm & Announcement System of the Turkish Submarine and the main power unit of our PBX operating the system)

• Redundant using

• Hot-plug design

• 1.5kW + 1.5kW=3kW output power

• Use of Hold-up capacitor block

• Lead-acid battery charge unit design

• MIL-STD-810G

• MIL-STD-461F

​​

GPS / INS guided ammunition main power unit design

• Redundancy

• Use of Hold-up capacitor block

• Mil-STD-1553 signal

• RTCA / DO-160 Protection

• DO-160

• Compliance with MIL-STD-704A/B/C/D/E/F support (All of them -A/B/C/D/E/F-)

• MIL-HDBK-704-8

​​

Military internal communication system power circuits design

(Milgem Project: The design and military tests of the Alarm & Announcement System of the Turkish Battleship (Milgem) and the main power unit of our PBX operating the system)

• Redundancy

• A very discrete telecom dc-dc switcher design

• System Design

• MIL-STD-810G

• MIL-STD-461F

• MIL-STD-1275

​​

1kW different power units design for military ships

• MIL-STD-461

• MIL-STD-1399 (For Navy)

• MIL-STD-810

​

200W led power supply design

• IEC 60950(EN 60950)

• IEC 61000-X-X (EN 61000-X-X)

• IEC 55022 (EN 55022)

​​

Discrete Industrial and Telecom power supply(DC-DC / AC-DC) design between 6w-600w

• IEC 60950(EN 60950)

• IEC/EN  62368-1

• IEC 61000-X-X (EN 61000-X-X)

• IEC 55022 (EN 55022)

• IEC 55032 (EN 55032)

• IEC 55011 (EN 55011)

• IEC 55024 (EN 55024)

​​

Assorted military and commercial backplane PCB cards design (Power and signals)

​

Many large and small DC-DC, AC-DC, PFC power supply card designs

​

Designing and verifying AC-DC&-48VDC and DC-DC&-48VDC isolated&non-isolated Telecom power supplies